On this page
- What a hospital bed is, electrically
- What four bed manuals say
- How big a UPS: size to the rating
- Runtime: the pump decides it, not the bed
- Worked through: an Invacare CS7 with a mattress pump
- The two answers you will find, and which is right
- Setting it up
- What this answer does not cover
- Frequently asked questions
Yes. A hospital bed is a fair load for a UPS, and Invacare's own manual points to one. It says a user who needs the CS bed to keep working through power interruptions should power it "from an uninterruptible power supply or a battery." The UPS has to be big enough for the bed's rated current, which is 420 to 480 VA on the beds below. How long it lasts is a different question. The motors run in short bursts, so the always-on mattress pump decides the hours.
This page covers the power engineering. It is not medical advice. How a person is moved, turned or kept safe in a long outage belongs in the care plan, and our medical equipment guide covers that side.
What a hospital bed is, electrically
A home-care or facility hospital bed is a frame with motors that move it. Each motor drives an actuator, a rod that pushes the head section, the knee or foot section, or the whole frame up and down (the "Hi-Lo"). A full electric bed has a motor for all three. A semi-electric bed motorizes the head and foot and uses a hand crank for height. Medline's MDR107002L is that type: "2 Motor, 1 Crank".
The motors do not run on wall power directly. A control box plugs into the outlet and turns 120 V AC into low-voltage DC. On the Invacare CS beds it puts out "24 VDC (70W max)", and every actuator is 24 V DC. Three numbers from the manuals matter for a UPS:
- Rated input current. The most the control box draws from the outlet while motors run.
- Duty cycle. How long the motors may run before they must rest. Both Invacare and Joerns give "10%": 2 minutes on, then 18 minutes off.
- Outage provision. What the maker built in for a power failure, if anything.
What four bed manuals say
No single manual answers the UPS question on its own. Put side by side, they do. The table holds only what each manual states.
| Bed | Rated input | Duty cycle | Outage provision | Extension cord |
|---|---|---|---|---|
| Invacare CS Series (CS3 to CS9FX600) | 3.5 A max; outlet rated at least 6 A | 10% (2 min on, 18 off) | Optional built-in battery back-up, not offered on every model | "DO NOT use an extension cord" |
| Joerns UltraCare XT | 4.0 A | 10% (2 min on, 18 off) | Portable 24 V backup battery, P/N N511, 20 to 25 cycles a charge | Not stated |
| Drive Delta 1000 (item 15033) | Not in the manual text | Not stated; thermal cutout | 9 V battery (sold separately) on the motor | Allowed: 3-wire, at least 16 AWG |
| Medline Home Care Bed (MDR107002L, MDR107003L) | Not in the manual text | Not stated | Emergency crank for each function | Not stated |
The Invacare battery comes with one condition worth knowing. In an outage, the manual says, "the bed can be powered by its internal battery but MUST remain plugged into the grounded outlet for proper grounding." The battery is charged "through the controller" and should be "tested monthly."
The Joerns battery is a facility item. It plugs into a socket at the foot end, charges in a wall charger in about four hours, and lasts about 3.5 years. Joerns says one battery "can typically raise and lower the bed, constituting one cycle, 20 to 25 times on single, full charge." It recommends at least one battery for every 25 beds.
Drive says that with the 9 V battery installed, "the motor can be operated in the event of a power failure." It says to check that battery and replace it every year. Medline's emergency crank "allows manual bed adjustment in the event of a power failure." It fits on the exposed shaft for the head, foot or Hi-Lo, and must come off once power is back.
How big a UPS: size to the rating
A UPS has two limits: VA (volts times amps) and watts. The bed's manual gives amps, so the safe move is to turn them into VA and then pick a UPS whose watt rating is at least that big. That covers the bed whatever its power factor, the gap between VA and real watts explained in VA vs watts.
Joerns UltraCare XT: 120 V x 4.0 A = 480 VA
A 600 VA / 360 W unit falls short of both on paper. An 850 VA / 510 W unit clears both. A 1000 VA / 600 W or a 1500 VA / 900 W tower clears them with room for the mattress pump. On 230 V Invacare models the rating is 1.5 A, or 345 VA.
That rating is a ceiling, not the running draw. The Invacare control box can deliver at most 70 W to its motors, and only while a button is held. Even with the losses in the box, a real move uses a fraction of 420 VA. Size to the rating anyway: it is the number the maker stands behind, and the UPS must not overload when two motors start at once.
Runtime: the pump decides it, not the bed
The duty cycle caps the motors at 2 minutes in every 20. For the other 18, and for most of a night, the bed only powers its control box. None of the four manuals gives that idle figure, so measure yours with a plug-in meter; see how to measure power draw. The table assumes 5 W. Swap in your reading in the UPS runtime calculator.
A bed for someone at risk of pressure sores usually carries an alternating pressure mattress, and its pump runs all the time. The home pumps in our air mattress pump guide are rated 7 to 12 W. The table uses 12 W.
The estimates use the calculator's model: new sealed lead-acid batteries, a Peukert exponent of 1.25 against the 20-hour rating, 88% inverter efficiency and 8 W of UPS overhead. Why UPS runtime is not linear explains each term.
| UPS class (battery) | Bed idle, 5 W | Bed idle + 12 W pump | Motors at 420 VA ceiling | Motors at 480 VA ceiling |
|---|---|---|---|---|
| 850 VA / 510 W (1 x 12 V 9 Ah) | 5 h 41 min | 2 h 31 min | 4 min | 4 min |
| 1000 VA / 600 W (2 x 12 V 7 Ah) | 9 h 53 min | 4 h 22 min | 8 min | 6 min |
| 1500 VA / 900 W (2 x 12 V 9 Ah) | 13 h 31 min | 5 h 58 min | 10 min | 9 min |
| 2200 VA / 1650 W (2 x 12 V 18 Ah) | 29 h 15 min | 14 h 12 min | 24 min | 21 min |
The motor columns are a worst case. They treat every VA of the rating as a watt and assume the motors run nonstop, which the duty cycle forbids. Read them as a budget instead: on a 1500 VA tower, each minute of motor at the full rating costs about a tenth of the battery. Real moves cost less, because the box can only deliver 70 W.
Worked through: an Invacare CS7 with a mattress pump
Take an Invacare CS7 at 120 V with a 12 W alternating pressure pump. Suppose both share a 1500 VA / 900 W pure sine tower, and the outage starts at 10 pm.
Standby load: 5 W (assumed bed idle) + 12 W (pump) = 17 W
Standby runtime: about 5 h 58 min, to roughly 4 am
Now add the moves. Say a caregiver raises the head twice in the night and lowers it again, four moves of 30 seconds each. That is 2 minutes of motor time. At the worst-case budget of a tenth of the battery per minute, it costs about a fifth, so the 6 hours shrink to a little under 5. Real moves cost less, since the box delivers at most 70 W. Either way the pump is the main load. If the bed alone sat on the UPS, the same battery would last about 13.5 hours.
Two things in that walkthrough are not yet known for any real bed: its true idle draw and how long its moves take. A meter and a stopwatch settle both in five minutes.
The trap: a bed that idles too quietly
APC says Back-UPS models with No-load Shutdown turn off "while operating on battery power when the attached load is less than 15 watts," after 15 minutes. A bed on its own may well idle below that. A 7 W pump on its own does too. If the UPS shuts itself off, the bed will not move when someone needs it at 3 am. Check your UPS manual for the feature and switch it off, or make sure the measured load stays above 15 W.
The two answers you will find, and which is right
One answer says beds are wall-only: the manuals ban extension cords, so a UPS must be wrong too. The other says a bed needs a big power station because it has motors. Both miss what the manuals say.
The extension cord rule is real but it differs by maker. Invacare bans extension cords and wants a grounded outlet rated at least 6 A. Drive allows a three-wire cord of at least 16 AWG with "the same or higher electrical rating" as the bed. Neither rule is about a UPS. Invacare, the stricter of the two, is the one whose manual recommends a UPS. Read together, the safe setup is the bed plugged straight into a UPS outlet, and the UPS plugged straight into a grounded wall outlet, with no cord or strip in between.
The power station answer overrates the bed. A 70 W motor supply that runs 2 minutes in 20 is a light load. A power station only earns its place when the outage outlasts a tower's battery; see UPS vs portable power station.
Bottom line
Use a UPS whose watt rating is at least the bed's rated amps times 120 V: 510 W or more covers both beds here. Pick 1500 VA or larger if a mattress pump shares it, because the pump sets the hours. Keep the maker's own backup, whether battery or crank, ready for when the UPS runs out.
Setting it up
- Read the bed's label or manual for its rated amps and voltage, and note whether it has a built-in battery or a crank.
- Plug the bed straight into a battery outlet. No power strip or extension between them; see plugging a UPS into a power strip. Keep the UPS on a grounded wall outlet the whole time. The Invacare manual requires the bed to stay grounded even on its own battery.
- Route the cords clear of the frame. Both Invacare and Drive warn against cords that can be pinched or tangled as the bed moves.
- Check the outlet marking on facility beds. Joerns says that with a hospital-grade plug, grounding is reliable only in a receptacle "marked hospital-grade."
- Turn off No-load Shutdown if your UPS has it, or confirm the load stays above 15 W on battery.
- Test it. With the pump running, switch off the breaker and run one move on battery. Prefer pure sine output; no manual here asks for it, but it removes doubt (see pure sine vs simulated sine). Retest yearly, as lead-acid batteries fade; see when to replace a UPS battery.
Respect the duty cycle on battery. If a bed overheats, Invacare and Drive both say it can stop responding for "up to 30 minutes" while its thermal protection resets. A pause between moves avoids that, and it saves battery too.
What this answer does not cover
These figures come from four manuals. Your bed's label governs, and a bed with no stated rating has to be measured, not guessed. A UPS keeps the bed moving and the pump running. It does not replace the maker's own backup, so keep the 9 V battery fresh, the built-in battery tested, or the crank where a caregiver can find it. Facility beds on hospital-grade circuits, and beds with a powered surface built into the frame, need their own figures. Consumer UPS units are not certified as medical electrical equipment. Whether a person can go without position changes or a pump for an hour or a night is a question for the care team. Outages longer than a tower's battery need a plan the supplier approves, which the medical equipment guide walks through.
Frequently asked questions
How many amps does a hospital bed draw?
The manuals checked here rate it at 3.5 A for the Invacare CS Series at 120 V (1.5 A on 230 V models) and 4.0 A for the Joerns UltraCare XT. That is a maximum while the motors run. The Invacare control box delivers at most 70 W to the 24 V DC motors, so the bed uses far less than the rating suggests most of the time. Size the UPS to the rating anyway.
Can I use an extension cord with a hospital bed?
It depends on the maker, and they disagree. Invacare's CS manual says "DO NOT use an extension cord" and wants a grounded outlet rated at least 6 amps. Drive's Delta 1000 manual allows a three-wire extension cord of at least 16 AWG with the same or higher rating as the bed. Follow your own bed's manual, and never use a three-to-two prong adapter.
What happens to an electric hospital bed in a power outage?
Without a UPS, it stops where it is. What comes next depends on the bed. Some Invacare CS beds have an optional built-in battery. Joerns sells a portable 24 V battery that plugs into the foot end. The Drive Delta 1000 takes a 9 V battery for power-failure use, and Medline's semi-electric and full electric home care beds come with an emergency crank.
Does a hospital bed need a pure sine UPS?
None of the four manuals cited here states a waveform requirement. The motors run on 24 V DC from the control box. A pure sine UPS removes the question, so choose one if you are buying new, and test the bed on battery either way.
Can the bed and the mattress pump share one UPS?
Yes, if the UPS is sized for the bed's rated current. The pump adds 7 to 12 W on the home pumps we checked, which hardly changes the size but sets most of the runtime. On a 1500 VA / 900 W tower, a 12 W pump plus 5 W of bed idle runs about 6 hours between moves.
Sources and further reading
- Invacare: CS Series Beds user manual, Part No 1153410 (electrical warnings, EMC table, electrical specifications, battery back-up)
- Joerns Healthcare: UltraCare XT bed frames user-service manual, 6110045 Rev I (electrical specifications, backup battery N511)
- Drive Medical: Delta 1000 Ultra Light Plus Full Electric Bed, item 15033, owner's assembly and operating manual
- Medline: Home Care Bed owner's assembly and operating manual, MDR107002L, MDR107003L, MDR107000P
- APC by Schneider Electric FAQ000210003: Back-UPS No-load Shutdown