What Size UPS Do You Need for a Mac mini or Mac Studio?

For a Mac mini, almost any pure sine UPS is big enough: Apple rates the current model for 155 W, which fits under 80% of a 600 VA / 360 W unit with room for a display. A Mac Studio is rated for 480 W, so it needs a 1000 VA / 600 W unit at minimum and is happier on a 1500 VA tower. Runtime is set by what the Mac actually draws, which Apple also publishes: 65 W at full load for a Mac mini M4, about 1 hour 34 minutes on a 1500 VA unit.

On this page
  1. What Apple says each Mac draws
  2. Which number to size the UPS on
  3. How long a UPS runs each Mac
  4. Pure sine, and why the Mac's supply decides it
  5. Let macOS do the shutdown
  6. What else belongs on the same UPS
  7. Where these numbers stop applying
  8. Frequently asked questions

Apple is unusually open about how much power its desktops use. Every Mac mini, iMac, Mac Studio and Mac Pro has a support page listing its idle and maximum draw, and every current spec page lists a maximum continuous power rating. The two numbers differ by a factor of two or more, and most of the confusion about sizing a UPS for a Mac comes from picking one of them and ignoring the other. You need both: one to choose the UPS, the other to know how long it will last.

What Apple says each Mac draws

Apple's support pages state that the watts are "measured from the wall power source and includes all power supply and system losses. Additional correction is not needed." Max means "running a compute-intensive test application that maximizes processor usage and therefore power consumption." For the Mac Studio, Apple adds that "No external peripherals are attached during testing" and that the figures reflect a 20.2°C (68.4°F) room; "Increased ambient temperatures require faster fan speeds which increases power consumption."

Apple's published power figures for Apple silicon desktops (configuration as tested by Apple)
ModelTested configurationIdleMaxRated max continuous
Mac mini (M1, 2020)16 GB, 2 TB6.8 W39 W (CPU max)Not listed here
Mac mini M2 (2023)24 GB, 2 TB7 W50 W (CPU max)Not listed here
Mac mini M2 Pro (2023)32 GB, 8 TB7 W100 W (CPU max)Not listed here
Mac mini M4 (2024)16 GB, 256 GB4 W65 WNot listed here
Mac mini M4 Pro (2024)64 GB, 8 TB5 W140 WNot listed here
Mac mini (M6)16 GB, 256 GB4 W70 W155 W
Mac mini (M5 Pro)64 GB, 8 TB6 W145 W155 W
iMac 24-inch (2024, four ports)M4 10-core, 32 GB, 2 TB46 W105 W (CPU max)143 W power adapter
Mac Studio M4 Max (2025)36 GB, 512 GB6 W145 WNot listed here
Mac Studio M3 Ultra (2025)512 GB, 16 TB9 W270 WNot listed here
Mac Studio (M5 Max)36 GB, 512 GB7 W200 W480 W
Mac Studio (M5 Ultra)512 GB, 16 TB9 W385 W480 W
Mac Pro (2023)M2 Ultra 76-core GPU, 192 GB, 8 TB49 W330 WNot listed here

The continuous ratings come from Apple's current spec pages, which cover only the models on sale, so older rows show none. The iMac figures include its built-in display, which is why its idle draw is 43 to 46 W rather than single digits. The iMac also differs physically: it ships with a 143 W external power adapter, while the Mac mini and Mac Studio ship with only a power cord because their supplies are inside.

Which number to size the UPS on

Two answers circulate. One says a Mac mini draws 65 W, so a tiny UPS is plenty and the 155 W rating is irrelevant. The other says to size on the rating and ignore the measurement. Each is half right, because they answer different questions.

The rating decides whether the UPS can carry the Mac at all. Apple's measured maximum is a processor stress test with nothing plugged in, and a real desk has bus-powered drives, a hub and perhaps a charging phone hanging off the ports. Our reading is that the gap between 145 W measured and 155 W rated on a Mac mini M5 Pro, or between 385 W and 480 W on a Mac Studio M5 Ultra, is headroom for exactly that. A UPS sized below the rating can trip on overload the one day the Mac and its accessories peak together. The measured figure decides how long the battery lasts, because no Mac runs at its rating continuously.

Our rule: capacity from the spec page, runtime from the support page

Take Apple's maximum continuous power, add the display and anything else on the battery outlets, and keep the total under 80% of the UPS's watt rating, the margin CyberPower's CP1500PFCLCD manual asks for. Then read runtime from Apple's measured Max plus the same accessories. For the current Mac mini that is 155 W / 0.8 = 194 W before a display, which any 600 VA / 360 W unit clears. For the current Mac Studio it is 480 W / 0.8 = 600 W, which is exactly a 1000 VA / 600 W unit with nothing else attached. That is why we put a Mac Studio on a 1500 VA tower.

Watts are the number to check, not VA; VA vs watts explains why a "1500 VA" box may deliver only 900 W, and UPS load percentage covers what running near 100% does to a unit.

How long a UPS runs each Mac

These estimates use the model behind our UPS runtime calculator: new sealed lead-acid batteries, a Peukert exponent of 1.25 referenced to the 20-hour rating, 88% inverter efficiency and 8 W of inverter overhead. Watt ratings and battery sizes are typical for each class; check your own unit's label. Each column is the Mac alone at Apple's measured Max, so add your display before reading across.

Estimated runtime at Apple's measured maximum draw, computer only (new batteries, room temperature)
UPS class (typical watts, battery)Mac mini M4, 65 WiMac M4, 105 WMac mini M4 Pro, 140 WMac Studio M5 Max, 200 WMac Studio M3 Ultra, 270 WMac Studio M5 Ultra, 385 W
600 VA (360 W, 1 x 12 V 7 Ah)29 min17 min12 min8 min5 minOver rating
850 VA (510 W, 1 x 12 V 9 Ah)39 min23 min16 min11 min7 min5 min
1000 VA (600 W, 2 x 12 V 7 Ah)1 h 9 min40 min28 min19 min13 min8 min
1500 VA (900 to 1,000 W, 2 x 12 V 9 Ah)1 h 34 min54 min39 min25 min18 min11 min
2200 VA (2 x 12 V 18 Ah)3 h 43 min2 h 9 min1 h 32 min1 h 0 min42 min27 min

Here is the arithmetic for a Mac mini M4 Pro on a 1500 VA tower such as the CyberPower CP1500PFCLCD (1500 VA / 1000 W, two 12 V 9 Ah batteries in its RB1290X2 set):

Battery draw = (140 W + 8 W) / 0.88 = 168 W, or 7.0 A at 24 V
Runtime = 20 h x (9 Ah / (7.0 A x 20 h))^1.25 = about 0.65 h, or 39 min

Two things stretch these numbers in practice. A Mac rarely sits at its stress-test maximum: at the M4's 4 W idle the same tower lasts many hours, and ordinary office work falls between the two. And macOS should be shutting the Mac down within minutes of the outage, not running it flat. Two things shrink them: an aged battery, and the display. Why UPS runtime is not linear explains why doubling the load more than halves the runtime.

Add the display, because Apple does not

Apple's Studio Display specifications list a line voltage of 100 to 240 V and a 96 W host charging port, but no power consumption figure. The only reliable number for your display is a measured one: put a plug-in meter between it and the wall at your usual brightness (how to measure power draw). As an illustration only, a display drawing 30 W next to a Mac mini M6 at 70 W makes a 100 W load, which a 1500 VA tower runs for about 58 minutes and a 600 VA unit for about 18. If a MacBook draws its charge through the display's 96 W host port, that is load on the UPS too.

Pure sine, and why the Mac's supply decides it

Forum threads on Mac Studio UPS choices split the usual way: some owners report a simulated sine unit working fine, others say it shuts the Mac off at the moment of transfer. A rule from ENERGY STAR explains which side to bet on. Its Version 9.0 computer specification says an internal power supply "with maximum rated output power greater than or equal to 75 watts shall meet both minimum efficiency requirements and minimum power factor requirements," and the minimum power factor is 0.90 at 50% load. Apple's spec pages list the Mac mini and Mac Studio as ENERGY STAR certified, and both run from an internal supply rated well above 75 W.

A power factor of 0.90 is the territory of active power factor correction, and CyberPower's manual for its sine wave CP1500PFCLCD makes the same connection, saying ENERGY STAR "mandates Active PFC for all power supplies over 100 watts" and that the UPS "supports High Efficiency power supplies with Active Power Factor Correction." Active PFC power supplies explains why those are the supplies that can drop out on a stepped wave. That some Macs ride through on simulated sine does not make it safe; it means that supply, at that load, on that UPS, happened to tolerate the transfer.

Bottom line

Put a Mac mini, Mac Studio or Mac Pro on a pure sine UPS. The iMac's external 143 W adapter falls under ENERGY STAR's external supply rules, which set an efficiency level and no power factor requirement, so the spec tells you nothing about it either way. We would still buy pure sine for an iMac, because the downside of guessing wrong is the crash the UPS was bought to prevent. Pure sine vs simulated sine covers the waveforms.

Let macOS do the shutdown

Apple's guide is short: "Some UPS devices run until their batteries are expended and then shut down. With other UPS devices, you can connect the device to the computer's USB port and set options for it using Energy settings." Once the UPS's USB data cable is connected, choose Apple menu, System Settings, Energy, then UPS Options, and pick when to shut down. "If you choose more than one option, the Mac desktop computer shuts down when the first condition is met." No vendor software is needed. Our macOS UPS settings guide covers the three triggers, pmset, and how to test, and UPS not detected by computer helps if the options never appear.

  1. Plug the Mac and its display into battery outlets. Printers, speakers and desk lamps go on the surge-only side.
  2. Connect the USB data cable from the UPS to the Mac, then check that UPS Options appears in Energy settings.
  3. Set a time-on-battery trigger that is no more than half the table's runtime for your Mac plus display. If half the runtime is under 5 minutes, the UPS is too small for that Mac.
  4. Turn on restart after a power failure. Current macOS calls it Start up when power is connected, with Never, After power failure and Always; older versions have a Start up automatically after a power failure checkbox.
  5. Pull the UPS's plug from the wall with work saved, and watch the Mac shut itself down on schedule.

Step 4 has a catch. "After power failure" turns the Mac on "when reconnected to power if the computer was on before a power failure." If the outage ends while the Mac is shutting down and the UPS never cuts its outlets, the Mac never sees the power go and come back, so it stays off. The same trap catches NAS boxes; the NAS guide covers making the UPS drop its output after shutdown.

What else belongs on the same UPS

A Mac that keeps running while the router is dark can save files but cannot finish a call or an upload. The modem and router guide puts a modem or ONT, router and switch at roughly 15 to 40 W, a small addition to the load, and the home office guide plans the whole desk. An external RAID enclosure or NAS on the same unit should get its own shutdown signal, since macOS has no built-in way to pass the UPS signal on to other machines; Network UPS Tools is the usual way to share one.

Where these numbers stop applying

  • Other configurations. Apple tests one configuration per row. A Mac Studio with less memory or a smaller SSD may draw less at its maximum, but the continuous rating is what the UPS must cover, and it does not change with configuration on the current spec pages.
  • Intel Macs. Older models draw far more: Apple lists 295 W at CPU max for a 2020 27-inch iMac and 902 W for a fully loaded 2019 Mac Pro. Use their rows on Apple's pages, not the Apple silicon figures here.
  • Hot rooms. Apple measured the Mac Studio at 20.2°C and says higher temperatures raise power through fan speed. A Mac in a warm closet draws more than the table assumes.
  • 230 V regions. Apple's watts are wall measurements and the Macs accept 100 to 240 V, so the watts carry over. UPS models, battery sets and watt ratings differ by region.
  • Aged batteries. The runtimes are for new batteries. Run a runtime calibration once a year and expect less as the battery ages.

Frequently asked questions

How many watts does a Mac mini use?

Apple measures the Mac mini M4 at 4 W idle and 65 W at maximum, the M4 Pro at 5 W and 140 W, the M6 at 4 W and 70 W, and the M5 Pro at 6 W and 145 W. Apple's figures are taken at the wall and include power supply losses. The current Mac mini is rated for 155 W maximum continuous power, which is the figure to size a UPS on.

Is a 600 VA UPS enough for a Mac mini?

Yes for capacity: a 600 VA / 360 W unit carries the Mac mini's 155 W rating at 43% load, leaving room for a monitor and network gear. Runtime is the limit. A 600 VA unit with one 12 V 7 Ah battery gives about 29 minutes at the M4's 65 W maximum and about 12 minutes at the M4 Pro's 140 W, before adding a display.

Does a Mac Studio need a pure sine wave UPS?

Buy one. The Mac Studio runs from an internal supply rated for 480 W, and ENERGY STAR requires internal supplies of 75 W or more to reach a power factor of 0.90. That is the class of supply that can misbehave on a stepped simulated sine wave. Some owners report no trouble on simulated sine units, but that is one supply at one load, not a rule.

Will my Mac turn back on by itself after a power outage?

Only if you set it to. In Energy settings, choose After power failure under Start up when power is connected (older versions: Start up automatically after a power failure). It fires when the Mac actually loses power and gets it back, so if the UPS keeps its outlets on after the Mac shuts down, the Mac stays off until you press the button.

Should the Studio Display go on the UPS too?

Yes, on a battery outlet, or you will have a running Mac and a black screen with no way to save your work. Apple's Studio Display specifications list line voltage but no power consumption figure, so measure it with a plug-in meter and add it to the Mac's watts before reading the runtime table.

Sources and further reading

  1. Apple Support: Mac mini power consumption and thermal output (BTU) information
  2. Apple Support: Mac Studio power consumption and thermal output (BTU) information
  3. Apple Support: iMac power consumption and thermal output
  4. Apple Support: Mac Pro power consumption and thermal output (BTU/h) information
  5. Apple: Mac mini technical specifications
  6. Apple: Mac Studio technical specifications
  7. Apple: iMac technical specifications
  8. Apple: Studio Display technical specifications
  9. Apple Mac User Guide: Set when your Mac shuts down while using a UPS
  10. Apple Mac User Guide: Energy settings on a Mac desktop computer
  11. ENERGY STAR Program Requirements for Computers, Version 9.0 (internal power supply efficiency and power factor, section 3.2.2)
  12. CyberPower: CP1350PFCLCD / CP1500PFCLCD user manual