Why Does My UPS Trip the GFCI Outlet?

Because a UPS and everything plugged into it leak a little current to ground by design, and a GFCI counts that as a ground fault. UL 943 lets a Class A GFCI trip anywhere from 4 to 6 mA, while UPS makers allow the UPS and its loads up to 3.5 mA combined, so one or two extra loads can push a setup into the trip band. Move loads off the UPS, try a different GFCI, or use a circuit the code does not require to be GFCI protected.

On this page
  1. Leakage that is there by design
  2. The leakage budget, from the manuals
  3. Confirm it is leakage, not a real ground fault
  4. Three fixes, in order
  5. Where the NEC requires GFCI, and where it does not
  6. On battery, the GFCI protects nothing behind the UPS
  7. Where this answer stops applying
  8. Frequently asked questions

A GFCI does not know what a UPS is. It compares the current leaving on the hot wire with the current returning on the neutral, and when the difference is large enough it opens. A UPS, and every computer, monitor and router plugged into it, sends a small current to the ground wire on purpose, through the capacitors in its noise filter. That current never comes back on the neutral, so the GFCI treats it exactly like current flowing through a person.

Leakage that is there by design

APC's support note on this exact complaint puts it plainly: "UPS systems and computer equipment exhibit leakage currents. These currents are a natural result of the common mode filters present in computers and UPSs." The same note says the leakage can be "large enough to 'fool' the GFCI and cause it to trip," after which the UPS, seeing its input disappear, carries on from the battery.

The symptom looks like a private outage: the UPS beeps on battery while every other circuit stays on, and pressing the GFCI's reset button restores power until the next trip. If the UPS is also transferring to battery when the GFCI has not tripped, that is a different problem, covered in UPS keeps switching to battery.

The leakage budget, from the manuals

The GFCI's side of the equation is fixed by UL 943, the U.S. standard for these devices. As IAEI Magazine summarizes it, "Class A ground-fault circuit interrupters trip when the current to ground is 6 mA or higher and do not trip when the current to ground is less than 4 mA." The 4 mA floor exists precisely so that normal equipment leakage does not trip them. Between 4 and 6 mA the standard leaves it to the device. The equipment side comes from the UPS makers:

UPS leakage figures and the GFCI trip band, from manufacturer documents
SourceWhat it coversFigureAgainst a Class A GFCI
UL 943 (via IAEI)Class A GFCI, must not tripbelow 4 mASafe zone
UL 943 (via IAEI)Class A GFCI, must trip6 mA or moreAlways trips
APC FA158861Any Back-UPS model, by itselfless than 1 mAWell clear
APC FA158861, worked exampleLoad 1 (2 mA) + Load 2 (1 mA) + UPS (0.5 mA)3.5 mA0.5 mA under the floor
CyberPower Value 1200E/1500E/2200E manualCeiling for the UPS and connected loads combined3.5 mA0.5 mA under the floor
Eaton 9E 6-20 kVA manualHardwired UPS, by itselfapprox. 8 mAAbove the must-trip level before any load

CyberPower's wording is that "the sum of the leakage currents of the UPS and the connected loads does not exceed 3.5mA." APC makes the same point: "the leakage current measured on the output of the UPS will include the leakage current of the load as well as the UPS." In other words, the UPS is not the leak. It is the junction where every load's leak meets on one plug, and the GFCI measures the total.

Two caveats on the table. The CyberPower and Eaton documents are for 230 V models, so read them as the industry's budget for pluggable equipment rather than as a 120 V measurement. And none of these documents gives a typical leakage figure for a PC or a monitor, so this page does not invent one.

Our arithmetic: the budget leaves half a milliamp of margin

A setup that meets the 3.5 mA ceiling exactly is 0.5 mA under the point where a GFCI is allowed to trip. Extend APC's own example with one more 1 mA load, a second monitor or a desktop, and the total becomes 4.5 mA: squarely inside the 4 to 6 mA band where one GFCI holds and the next one trips. That is why the same setup can hold on one GFCI and trip another, and why replacing the GFCI sometimes works and sometimes does not.

Confirm it is leakage, not a real ground fault

A GFCI that trips is doing its job until proven otherwise. Before treating the trips as a nuisance, rule out a real fault. This takes about ten minutes:

  1. Unplug every load from the UPS and reset the GFCI with only the UPS connected and switched on. Leave it for a day if the trips have been intermittent.
  2. If the UPS alone trips it, that is not normal leakage: APC puts a Back-UPS at under 1 mA, a quarter of the no-trip floor. Look for water in the receptacle box (common in garages and outdoors), a damaged cord, or a worn GFCI. Try the UPS on another GFCI, and plug a lamp into this one to see whether it trips with nothing electronic on it.
  3. If the UPS alone holds, add the loads back one at a time, waiting a while after each. Note which one brings the trip back. That load is not necessarily faulty; it may simply be the one that pushed the total over.
  4. Plug that last load straight into the GFCI, without the UPS. If it trips the GFCI on its own, the load has a fault and needs attention before anything else.
  5. Check the UPS indicators. A lit site wiring fault light means the receptacle itself is suspect; see site wiring fault light.

Three fixes, in order

1. Take loads off the UPS

Every load removed takes its share of leakage with it. Anything that does not need to ride through an outage, such as a second monitor, speakers, a printer or a desk lamp, can go on a receptacle that is not on the GFCI. A laser printer should never be on the battery outlets anyway; see UPS for a laser printer. Splitting the loads across two smaller UPS units on different circuits also works, because each GFCI then sees only its own share. Do not plug the UPS into a power strip to reach a different receptacle: makers prohibit it (here is why).

2. Replace the GFCI

APC's first suggestion is to replace the GFCI or try another brand, adding that "the circuit breaker type GFCI devices are generally of higher quality." This works when the total sits inside the 4 to 6 mA band, because each device trips at its own point in that band. It cannot work above 6 mA, where every Class A device must trip. If a new GFCI still trips, go back to fix 1.

3. Use a circuit that does not need GFCI, where the code allows

APC's note also suggests non-GFCI receptacles outside bathrooms and kitchens. The current National Electrical Code is stricter than that, so check the list below first. Never swap out a GFCI the code requires, never use a three-to-two adapter to break the ground path, and see site wiring faults and grounding for what a missing ground does to a UPS.

Where the NEC requires GFCI, and where it does not

The 2023 NEC, section 210.8(A), requires GFCI protection for 125 V through 250 V receptacles in these dwelling locations. Local jurisdictions adopt editions on their own schedule, so an older house or an earlier code cycle may differ; your local inspector is the authority.

2023 NEC 210.8(A) dwelling GFCI locations, and what each means for a UPS
LocationGFCI required?Typical UPS there
Kitchens (every receptacle, not just countertop, since 2023)YesRefrigerator, router on a counter: keep the load list short
Areas with a sink and permanent food or beverage preparationYesWet bars, coffee stations
Within 6 ft of any sink, bathtub or showerYesUtility rooms, workshops with a sink
BasementsYesSump pump, network rack, boiler
Garages and accessory buildingsYesGarage door opener, freezer
Laundry areasYesRarely a UPS location
Crawl spaces at or below grade, outdoors, boathousesYesPumps, cameras
Bathrooms and indoor damp or wet locationsYesRarely a UPS location
Bedrooms, living rooms, home offices, dining rooms, hallwaysNot listed in 210.8(A)The easy home for a computer UPS

The exceptions are narrow: a receptacle supplying only a permanently installed premises security system, a receptacle built into a bathroom exhaust fan, and a not readily accessible receptacle for fixed snow-melting equipment that has its own ground-fault protection. None of them covers a sump pump, a garage door opener or a refrigerator. Mike Holt's commentary on the kitchen change spells it out: the range, refrigerator, disposal and microwave receptacles "will require GFCI protection."

Businesses fall under 210.8(B), which also covers kitchens and areas with sinks for food or beverage preparation. That is the setting of a 2014 Mike Holt Forum thread in which an engineer planning a point-of-sale UPS at a food counter worried that the UPS filters "may leak enough current to ground that it trips out the GFCI." If that is your situation, see UPS for a point-of-sale system.

On battery, the GFCI protects nothing behind the UPS

The same forum thread raises the point most guides miss. Once the GFCI trips, the UPS keeps its outlets live from the battery: "The computer, printer, monitor, and anything else plugged into that UPS will still be hot." The upstream GFCI sits on the input side and cannot see or interrupt anything on the output. That holds whether the GFCI tripped from nuisance leakage or from a real fault in a device plugged into the UPS.

That matters where water and people meet the loads: a sump pump in a basement pit, the heaters and pumps on an aquarium, or tools in a garage. One reply in the thread suggests the simple answer: "Use a portable GFCI plugged into the UPS."

Our analysis: a GFCI after the UPS solves both problems at once

A portable GFCI plugged into a UPS outlet protects the loads behind it on utility power and on battery, because it sits on the output. It also sees only the leakage of the loads plugged into it, not the UPS's own or that of the other outlets. Put the wet-location load (pump, aquarium gear) on that portable GFCI, and the dry electronics on the remaining UPS outlets. The wall GFCI still sees the total, so the load list still has to fit the budget above.

Where this answer stops applying

  • Large hardwired UPS units. Eaton's 9E manual says the unit "generates a leakage current of over 3.5 mA" and, in the protection section, approximately 8 mA, which any upstream ground-fault device must account for along with the load. Units like this do not belong behind a Class A GFCI; their protection is designed by an electrician.
  • Outside North America. UL 943 is harmonized with the Canadian and Mexican standards, so the 4 to 6 mA band applies across North America only. Residual-current devices elsewhere follow other standards; check yours before applying this page's arithmetic.
  • Arc-fault (AFCI) trips. These are a different mechanism with different causes; see site wiring faults and grounding.
  • A GFCI that trips with nothing plugged in, or trips after rain, is a wiring or moisture fault. Have it inspected before putting any UPS on it.

Frequently asked questions

Is it safe to plug a UPS into a GFCI outlet?

Yes. Nothing in the APC or CyberPower documents cited here forbids it, and the GFCI still protects everything upstream of the UPS input. The two catches are nuisance trips when the UPS and its loads leak close to 4 mA, and the loss of GFCI protection on the UPS outlets once the GFCI trips and the unit runs on battery.

Why does the GFCI trip only when the power comes back or the UPS switches over?

A GFCI responds to imbalance at a moment, and a setup that leaks just under the trip point has almost no margin. APC's FAQ puts the trips down to leakage from the common mode filters in UPS units and computers. If the GFCI holds with the UPS alone and trips only with the full load behind it, treat it as a leakage budget problem and remove loads.

Will a GFCI circuit breaker stop the nuisance trips?

It may. APC suggests trying a different GFCI and says breaker-type devices are generally of higher quality. A breaker is still a Class A device with the same 4 to 6 mA band, so it only helps a setup that sits inside that band. A setup leaking 6 mA or more will trip any Class A GFCI, breaker or receptacle.

Can I replace the GFCI with a standard outlet so the UPS stops tripping it?

Not where the NEC requires GFCI protection, which on the 2023 edition includes every kitchen receptacle, basements, garages, laundry areas and receptacles within 6 ft of a sink. In a room 210.8(A) does not list, such as a bedroom or home office, a standard receptacle is fine and is the better home for a UPS.

Does my UPS have its own GFCI protection on battery?

None of the manuals cited here says so. Treat the UPS outlets as unprotected while on battery. Where people or water are close, as with a sump pump or aquarium, a portable GFCI plugged into the UPS output covers those loads in both modes.

Sources and further reading

  1. Alan Manche, "GFCI and AFCI Basics," IAEI Magazine, May 16, 2012 (UL 943 Class A thresholds)
  2. APC by Schneider Electric FAQ FA158850: GFCI circuit breaker trips after UPS or SurgeArrest
  3. APC by Schneider Electric FAQ FA158861: Leakage current from APC Back UPS products
  4. CyberPower Value 1200E / 1500E / 2200E user manual
  5. Eaton 9E 6-20 kVA UPS user manual (leakage current notices)
  6. Mike Holt Enterprises, Understanding the 2023 National Electrical Code, Volume 1: 210.8 GFCI protection
  7. Laura Hildreth, "Powering Forward: Major Changes in the 2023 NEC," IAEI Magazine, July 1, 2025
  8. Mike Holt Forum: UPS on a kitchen GFI outlet (May 2014)