Can a UPS Run Heat Tape to Keep Pipes From Freezing?

Yes, for hours rather than days. Heat tape draws its length in feet times its watts per foot, so 9 feet runs about 45 to 63 W. A common 1500 VA UPS carries 63 W for about 2 hours 10 minutes nonstop, and longer when the cable's thermostat switches it off. Plug it through a portable GFCI on the UPS output, and insulate the pipe first.

On this page
  1. How many watts heat tape draws
  2. Worked example: 9 feet of Frost King HC9 on a 1500 VA UPS
  3. Runtime by cable
  4. The thermostat trap on a UPS
  5. Ground fault protection: the UPS output is not a GFCI
  6. Insulate first, then back it up
  7. If the outage runs long: drain the line
  8. UPS or power station for heat tape
  9. What this answer does not cover
  10. Frequently asked questions

Yes, a UPS can run heat tape in a power outage, but only for a few hours. Nine feet of tape draws about 45 to 63 W. A common 1500 VA UPS runs 63 W for about 2 hours 10 minutes if the tape stays on the whole time. A thermostat stretches that. So a UPS can carry a pipe through a short outage, not a long one.

First, the terms. Heat tape (also sold as heat cable or pipe heating cable) is an electric cable that lies along a water pipe. It warms the pipe so the water inside cannot freeze. It plugs into a normal 120 V outlet. Most plug-in kits for homes, like Frost King's HC series, are constant wattage: every foot gives the same heat whenever power flows. A built-in thermostat in the plug end turns the cable on and off. Self-regulating cable is different. Its output changes with the temperature of the pipe, so it makes less heat as the pipe warms. A UPS (uninterruptible power supply) is a battery box that keeps its outlets live when wall power fails.

How many watts heat tape draws

The rule is simple: watts = length in feet x watts per foot. WarmlyYours puts it the same way and gives an example. "A 30-foot, 7 W/ft kit draws 210 watts while energized." The only number you need from the box is the watts per foot.

Frost King rates every HC pipe cable from 3 to 30 feet at "120V, 7 Watts per foot." Its leaflet lists each model's total. They run from 21 W for the 3-foot HC3 to 210 W for the 30-foot HC30. Frost King's roof de-icing kits are a different product at "120V, 5 Watts per foot." That 5 W figure gets quoted for pipe tape too. The person who started the Green Building Advisor thread planned on "about 9ft, at 5 watts per foot." Frost King's own 9-foot pipe cable is 63 W, not 45 W. Read the box for the cable you own.

Published ratings for plug-in and cut-to-length heat cable (120 V)
CableTypeW/ftExample totalSource
Frost King HC3 to HC30 pipe cablesConstant wattage, built-in thermostat7HC9: 63 W; HC18: 126 WFrost King FAQ and leaflet
Frost King roof de-icing kitsConstant wattage (roof, not pipe)59 ft would be 45 WFrost King FAQ
WarmlyYours PRO-Tect PT-SR-120-08Self-regulating, hardwired89 ft: 72 W at ratingWarmlyYours (discontinued)
WarmlyYours PRO-Tect PT-SR-120-10Self-regulating, hardwired109 ft: 90 W at ratingWarmlyYours (discontinued)

Both WarmlyYours cables are marked discontinued. They still show what self-regulating cable is rated at. WarmlyYours notes that "self-regulating output" changes how much power the cable actually uses, so the rated figure is a planning number, not a fixed draw. WarmlyYours sells a plug-in kit, the SR-PLUG-KIT, to turn this hardwired cable into one that plugs in.

Worked example: 9 feet of Frost King HC9 on a 1500 VA UPS

Take a 9-foot run of metal pipe in a basement near a well tank, like the one in the Green Building Advisor thread. Put a Frost King HC9 on it. That is 9 feet at 7 W/ft, or 63 W. Plug it into a 1500 VA UPS with two 12 V 9 Ah batteries. That pair holds 216 Wh.

The method is the one in why UPS runtime is not linear. It uses 85% inverter efficiency and a Peukert exponent of 1.15. (The Peukert effect means a lead-acid battery gives less total energy the faster you drain it.)

Battery load = 63 W / 0.85 = 74 W, or 3.1 A at 24 V
Runtime = 20 h x (9 Ah / (3.1 A x 20 h))^1.15 = about 2.2 h, or 2 hours 10 minutes

That is the time if the cable never switches off. Frost King's thermostat turns the cable on "when the pipe temperature is below 38 F" and off above 45°F. Suppose the cable runs half the time in a cold room. The battery then gives about the same 2 hours 10 minutes of on-time, spread over roughly 4 hours 20 minutes on the clock. That is a ceiling, since the UPS also draws a little itself while the cable is off.

The same tape on a 750 VA UPS with one 12 V 9 Ah battery gets about 1 hour of on-time.

Runtime by cable

Here is the same math for each rating above, plus the longer Frost King kits. These are new-battery figures with the cable on all the time. A thermostat that cycles adds clock time on top.

Heat tape runtime with the cable on nonstop (85% efficiency, Peukert 1.15)
Cable load1500 VA, 2 x 12 V 9 Ah750 VA, 1 x 12 V 9 Ah
21 W (Frost King HC3, 3 ft)about 7 h 45 minabout 3 h 30 min
45 W (9 ft at 5 W/ft)about 3 h 15 minabout 1 h 25 min
63 W (Frost King HC9, 9 ft)about 2 h 10 minabout 1 h
72 W rated (9 ft of PT-SR-120-08)about 1 h 50 minabout 50 min
84 W (Frost King HC12, 12 ft)about 1 h 35 minabout 42 min
126 W (Frost King HC18, 18 ft)about 1 habout 27 min

For your own cable, put its watts into the runtime calculator. If you have a plug-in watt meter, you can check the real draw too; how to measure power draw shows how. The pipe has to be below the thermostat's turn-on point to see it draw anything.

Our analysis: "heat tape uses a lot of power" and "heat tape uses very little" are both true

On Green Building Advisor, Bill Wichers warned that electric resistance heat "uses a relatively large amount of power for the amount of heat you get." The post went on: "your battery backup is not likely to last very long." Another member wrote that with heat cable on the water line, "you really didn't notice the electricity." They are talking about two different budgets. Next to a house on utility power, 63 W is small. Next to a 216 Wh UPS battery, 63 W empties it in an afternoon. The question for an outage is never the watts alone. It is watts x hours against the battery's Wh. At 63 W, a full day is about 1,500 Wh, seven times what that UPS holds.

The thermostat trap on a UPS

A thermostat helps runtime. It can also switch the UPS off for good. When the pipe warms past 45°F, the Frost King cable stops drawing power. The UPS then sees almost no load.

APC says its "Back-UPS products with No-load Shutdown functionality enabled will shut down while operating on battery power when the attached load is less than 15 watts." That happens after 15 minutes. Once it is off, it stays off. When the pipe cools and the thermostat calls for heat, there is no power to answer it. Check your manual for this feature before winter. APC's FAQ shows how to switch it off in Program Mode. The same trap catches small loads like a reptile heat mat.

Self-regulating cable behaves differently. The poster in the thread noted that continuously variable cables "use power all the time." Whether that draw stays above 15 W depends on the cable and how warm the pipe is, so check for the cutoff either way.

Ground fault protection: the UPS output is not a GFCI

Heat cable makers want it on a ground fault protected outlet. Frost King's leaflet says to "plug into a ground fault protected electrical outlet," and its warning reads "Frost King recommends using a ground fault protected receptacle." WarmlyYours goes further. Its plug-in kit manual says that "to comply with the requirements of the National Electrical Code, ground-fault equipment protection must be used on each heating cable branch circuit." The reason it gives: "Arcing may not be stopped by conventional circuit protection." In other words, a damaged cable can arc and start a fire without tripping a normal breaker.

Here is the gap. Plugging the UPS into a GFCI outlet does not protect the cable once the UPS is on battery. The wall GFCI sits on the input side. It cannot see or cut anything on the UPS outlets, which stay live from the battery even after it trips. Our guide to why a UPS trips a GFCI found no UPS manual that says its outlets have their own GFCI. Treat them as unprotected on battery.

Put a portable GFCI on the UPS output

Plug a portable GFCI into the UPS battery outlet, then plug the heat tape into the GFCI. That protects the cable on wall power and on battery. Do not use an extension cord to reach it: WarmlyYours says pipe heat "should always be plugged directly into a receptacle." Never wrap the cable over itself. Frost King says "Never ever overwrap the heat cable!" because it "may cause the heating cable to overheat."

Insulate first, then back it up

Insulation does more for an outage than any battery. Frost King tells you to "wrap the entire pipe and cable with insulation." Its FAQ calls for "½ inch fiberglass insulation or any equivalent non-combustible insulation with vapor seal." For plastic pipe, Frost King suggests a layer of aluminum foil under the cable to spread the heat.

The thread's poster asked whether insulating the pipe and tape was worth it. Bill Wichers answered "Insulating is better." It holds the cable's small heat in the pipe. When the power is gone and the backup is flat, it also "keep[s] the pipe warmer for longer." So insulation helps in both cases: it makes the UPS last longer, and it buys time after the UPS is empty.

If the outage runs long: drain the line

A UPS gives you hours. A winter storm can take days. Once the battery is near empty, protect the pipe the other way: take the water out of it.

  1. Shut off the main water supply. On a private well, the well pump has already stopped, since no plug-in UPS can start it.
  2. Turn off the water heater. One Green Building Advisor member stressed turning off the water heater breaker whenever you shut the supply valves.
  3. Open faucets and valves. Malcolm Taylor wrote that "opening up valves or faucets to relieve pressure goes a long way." Taylor explained that the damage comes from pressure building up in lines with no outlet.
  4. Drain the low points. Bill Wichers described blowing the lines out with compressed air and pitching supply lines toward a low-point drain valve. That is a plan for a house left empty, not a fix mid-storm, but it shows what "drained" means.

Tankless water heaters have their own freeze protection that draws power. The tankless water heater guide covers what it needs.

UPS or power station for heat tape

A desktop UPS is built for minutes to a few hours. For heat tape through a night, a portable power station holds far more energy for the money. The poster in the thread planned to plug the tape into "the Ecoflow or Anker Solix power station version, not the APC computer type." Size it on the worst case, with the cable on the whole time. At 63 W, that is about 760 Wh for 12 hours and 1,500 Wh for 24, before inverter losses. A UPS that takes extended battery packs is the other way to get there.

Bottom line

Work out the watts first: feet x W/ft from the box. A 1500 VA UPS runs a 9-foot, 63 W cable for about 2 hours nonstop, and longer as the thermostat cycles. Turn off any light-load cutoff, and put a portable GFCI on the UPS output. Insulate the pipe before the cold comes. If the outage outlasts the battery, shut off the water and drain the line.

What this answer does not cover

The figures here come from Frost King and WarmlyYours data and one Green Building Advisor thread. Other cables have other ratings, so read your own box. The runtimes are estimates for new batteries and a cable that never switches off. No source here says how often a thermostat cycles, so the half-time case above is only a walkthrough. How fast an unheated pipe freezes depends on the room, the wind and where the pipe runs. Nothing cited gives a number for it. One member's view was that a reasonably modern, insulated, tight house "will not freeze up for, at the very least, days." Drafty old houses, the same post said, freeze "even when the heat is on." Treat that as one person's experience, not a rule. Heat cable is still a fire risk. Follow its maker's rules on layout, spacing and insulation, WarmlyYours says its cable is not for burial and not for use inside walls. Hardwired cable is wired into a circuit, not plugged in, and the NEC ground fault rules quoted above apply to it. Nothing here replaces those rules.

Test it on a cold night

When the pipe is below 38°F, plug the tape through the GFCI into the UPS. Check the power light on the plug. Then switch off the breaker that feeds the UPS. Note how long the UPS runs, and whether it stays on through a thermostat off cycle.

Frequently asked questions

How many watts does heat tape use?

Multiply its length in feet by its watts per foot. Frost King lists every HC pipe cable at 7 W/ft, from the 21 W HC3 to the 210 W HC30. WarmlyYours gives the same rule: a 30-foot, 7 W/ft kit "draws 210 watts while energized." A self-regulating cable's output changes with the pipe's temperature, so its rating is a guide, not a fixed draw. WarmlyYours says "self-regulating output" changes actual use.

Can I run heat tape from a portable power station?

Yes, and for a long outage it is the better tool. The Green Building Advisor poster planned exactly that, an EcoFlow or Anker unit rather than a computer UPS. Size it on the worst case: 63 W left on for 24 hours is about 1,500 Wh before losses. A thermostat that cycles will use less.

Will heat tape keep pipes from freezing with no power at all?

No. With the power and the backup both gone, the cable is just wire. What helps then is the insulation over it, which Frost King says to wrap over the whole pipe and cable. On Green Building Advisor, Bill Wichers said insulation helps "keep the pipe warmer for longer" once the room cools.

Why did my UPS turn off with the heat tape plugged in?

The thermostat may have switched the cable off. With nothing drawing power, an APC Back-UPS with No-load Shutdown turns off after 15 minutes on battery when the load is under 15 W. It then stays off when the thermostat calls for heat again. APC's FAQ shows how to switch the feature off.

Can I use an extension cord to reach the UPS?

WarmlyYours says it "does not recommend using an extension cord for permanent installations" and that pipe heat should plug "directly into a receptacle." Put the UPS where the cable's own cord reaches it. The portable GFCI plugs straight into the UPS outlet, and the cable plugs straight into the GFCI.

Sources and further reading

  1. Frost King: What is the wattage per foot on the roof de-icing kit? (120 V, 5 W/ft)
  2. Frost King: Heat Cables support FAQ (7 W/ft, 38°F on and 45°F off, insulation, no overwrapping)
  3. Frost King: Automatic Electric Heat Cable Kits, HC3A to HC30A
  4. Frost King (Thermwell): HC Series pipe freeze protection cable leaflet, 40200-001 Rev. 5 (watts by model, ground fault warning)
  5. WarmlyYours: PRO-Tect self-regulating heat tape for pipes, PT-SR-120-08 (8 W/ft) support page and FAQ
  6. WarmlyYours: PRO-Tect self-regulating heat tape for pipes, PT-SR-120-10 (10 W/ft)
  7. WarmlyYours: SR-PLUG-KIT plug-in conversion kit installation manual (ground fault protection and NEC notes)
  8. Green Building Advisor: Pipe freezing in power outage, how to prevent with battery back-up only (thread, January 2024 to December 2025)
  9. APC by Schneider Electric FAQ000210003: Back-UPS shuts down after 15 minutes on battery (No-load Shutdown)